Here you will find the highest quality parts for your Polaris RZR XP Turbo, including high clearance trailing arms and a-arms. More parts are constantly being designed and tested.
-
The RZR High Gear Spacer is an effective way to prevent losing high gear in your Polaris RZR or General. The high gear on the reverse shaft floats on a set of needle bearings and is held in place by a washer and retainer clip on each side. If you routinely try to shift gears without stopping the RZR, or letting the RPMs fully drop to idle, the shift dog puts undo stress bouncing on the side of the high gear. This stress can cause the retainer clip to pop out of its groove. That allows the high gear to shift over and can no longer be engaged. Sometimes the retainer clip breaks instead of just popping out of the groove, which can then get between the gear teeth and wreak havoc on your transmission. The RZR High Gear Spacer replaces the washer and retainer clip on one side and takes up the gap between the high gear and the bearing. We highly suggest installing one in your transmission along with our heavy duty bearing retainer plates. Fits Polaris RZR 900 XP, Polaris General, Polaris RZR 900 S, Polaris RZR XP 1000, Polaris RZR XP Turbo, Polaris RZR Turbo S, Polaris RZR Turbo R Due to the nature of this product and its intended use, it has no warranty.
-
This gear reduction consists of Polaris part #'s 3236689 and 3236690, also known as the Turbo R Gear Reduction. This is a stage 2 gear reduction consisting of the 23 tooth reverse gear shaft and the 50 tooth stage 2 gear that first came in the 2023 Polaris RZR Turbo R. This is a total reduction of approximately 43% across high, low, and reverse. We highly suggest you contact us before ordering gears unless you are absolutely sure what part numbers you are needing. This is because of the variations in gear reductions from the factory and compatibility. There is no warranty on Polaris gears and no returns. This product is not eligible for any discounts.
-
The new Rock Ready UTV Polaris RZR Single Packout Mount is the easiest way to add a Single Milwaukee Packout Tool Box or cooler to your RZR. This is the perfect addition to our double packout mount. The mount sits sideways in the rear portion of the bed making it compatible with our double mount for various toolbox and cooler (#48-22-8460) configurations. The single mount allows you to run the Yeti or Rtic 35 quart cooler in the front position and Milwaukee toolboxes in the rear position if you prefer to run a larger cooler. The mount is made from 1/8" aluminum to keep it light weight, strong, and to avoid rust. The price is for the single mount and installation hardware only. The tool boxes and cooler must be purchased separately.
- Made from 1/8" aluminum
- CNC laser cut and bent
- Ambidextrous mounting for left or right hand opening
- Powder coated black
- Made in the USA
-
This gear reduction consists of Polaris part #'s 3235774 and 3235989, also known as the 2 Seater Low Gear Reduction. It is a 29/64 tooth combination, which came in most 2017-2020 2 seater RZR XP Turbo transmissions. These gears can be installed in some 4 seater RZR Turbo transmissions to reduce only the low gear. This reduction is not as low as the Ranger Low Gear. We highly suggest you contact us before ordering gears unless you are absolutely sure what part numbers you are needing. This is because of the variations in gear reductions from the factory and compatibility. There is no warranty on Polaris gears and no returns. This product is not eligible for any discounts.
-
This gear reduction consists of Polaris part #'s 3235380 and 3235381, also known as the 4 Seater Gear Reduction. This is a stage 2 gear reduction consisting of the 27 tooth reverse gear shaft and the 46 tooth stage 2 gear. This reverse shaft and stage 2 came in most 4 seat machines and can be used to reduce the gears in some 2 seat machines. The total reduction is approximately 13% across high, low, and reverse. We highly suggest you contact us before ordering gears unless you are absolutely sure what part numbers you are needing. This is because of the variations in gear reductions from the factory and compatibility. There is no warranty on Polaris gears and no returns. This product is not eligible for any discounts.
-
Our new RZR Rear Center Console Delete Kit is the easiest way to get rid of your rear center console in your 4 seat RZR. This kit gives you the clearance needed to run a set of our Rock Ready UTV seat lowering bases with a bench seat in the rear. This kit is also great for those people wanting to make rear cargo racks as low as possible to lower the center of gravity. The aluminum plates are powder coated in a nice textured black to closely match the factory plastics.
- Made from 14 gauge aluminum
- CNC laser cut and bent
- Weighs less than the factory console
- Powder coated black
- Made in the USA
-
The new Rock Ready UTV Polaris RZR Milwaukee Packout Mount is the easiest way to add a Milwaukee Packout Tool Box to your RZR. The initial install is completely bolt in requiring common hand tools. It comes with hand knobs so that you can easily remove it to access the engine service panel. The Milwaukee Packout tool boxes (#48-22-8422) are an excellent storage solution. You can also mix and match the various Milwaukee boxes to fit your storage needs. Milwaukee even makes a 16 quart cooler (#48-22-8460) that works just like the Packout Compact Tool Box! Prices are for the mount only. The tool boxes and cooler must be purchased separately.
- Made from 1/8" aluminum
- CNC laser cut and bent
- Powder coated black
- Made in the USA
-
The new Rock Ready UTV Front Tow Hook is the easiest way to add a tow point to the front of your RZR. It also makes an excellent tie down point to make sure your RZR gets to and from the trail safely. The sleek, tucked design ensures you retain maximum approach angle so you're not banging it on the rocks. The tow hook mounts with (4) M10 bolts unlike several that just use 2 or 3. The hook fits most common winch hooks, soft shackles, and tow straps.
- Made from 1/4" steel plate and 5/8" round bar
- CNC laser cut and bent
- The round bar sticks out less than 2"
- Made in the USA
- Lifetime warranty
-
This gear reduction consists of Polaris part #'s 3235232 and 3236132, also known as the Ranger Low Gear Reduction. It is a 25/67 tooth combination. These low range gears come in newer Polaris Rangers. We highly suggest you contact us before ordering gears unless you are absolutely sure what part numbers you are needing. This is because of the variations in gear reductions from the factory and compatibility. This same low gear ratio came in some Polaris RZR's from the factory, such as the 2016 RZR XP Turbos. There is no warranty on Polaris gears and no returns. This product is not eligible for any discounts.
-
These weld-in washers are a great way to fix those egged out M12 bolt holes suspension components. Just drill the bolt hole out to 3/4" and weld these in. Purchase 16 weld-in washers to give your a-arm mounting points on your Turbo S an overhaul.
- Made from chromoly steel
- Increases the strength of the suspension mounting tab
- Greatly reduces the wear on the tab and bolt by increasing the surface area
- Harder more wear resistant material than the factory steel frame
- Fits M12 bolts
- Sold in sets of 4
-
-Adjustable recline angle (3.5°, 5.2°, 7°) -Can be used with or without the factory slider -More rear adjustment than the factory seat base -Lowers the back of the seat 2+” depending on the recline adjustment -Lowers the rear base of the seat 3/4" -CNC laser cut and formed -3/16” steel construction -Powder coated black -Includes all hardware and instructions -Choose Single or Pair -Fits 14-23 RZR XP 1000 2 and 4 seaters, 15-23 RZR 900/1000S 2 and 4 seaters, 16-23 RZR XP Turbo 2 and 4 seaters, 18-22 RZR Turbo S 2 and 4 Seaters, 18-22 RS1, 16-23 General 2 and 4 Seaters, Does not fit Pro XP Shipping Information: You must provide a physical shipping address. We will not ship seat bases to a P.O. Box.
-
Rock Ready UTV's heavy duty radius rod plate is the perfect add on to strengthen your radius rod mounting. We strongly suggest upgrading from the weak stock plate which is prone to bending, egging out the holes, and even tearing bolts through the plate. Greatly strengthen your radius rod mounting points by welding in a set of our weld bungs to eliminate those hard to get to nuts behind the transmission. The radius rod plate is available to fit the M10 and the M12 bolt sizes. The M10 uses a 15mm socket and the M12 uses an 18 mm socket.
- Made from 3/16" chromoly plate
- Laser cut and CNC bent
- Thicker, harder material to prevent wear on the bolt holes
- Available raw steel or powder coated black
- Made in the USA
- Fits 2014+ RZR XP 1000, 2016+ RZR XP Turbo, 2018+ RS1
